park tool IR-1.2 bicycle Internal Cable Routing Kit bottom bracket pedal disc brake pad spreader chain wear indicator rotor

IR-1.2 FEATURES

Includes four 250 cm (98") cables with attached magnets and unique fittings:

• Barbed adaptor – Threads into the end of brake & shift cable housing as well as hydraulic brake hose

• Rubber adaptor – Securely holds electronic shifting wire such as Shimano® Di2, SRAM® RED® eTAP®, FSA® K-Force® WE®, and Campagnolo® EPS

• Di2®-specific adaptor – Specially-designed connector clips into the end of the Shimano® E-tube® Di2® shift cable, and is perfectly sized to fit into frame holes as small as 6 mm

• Reverse-polarity magnet – Used in conjunction with any of the other guide cables – feeds into the opposite end and meets the leading cable in the middle, aiding in routing on frames with tricky interior shapes

CCP-22 FEATURES
Compatible with systems that use an M8 or M10 threaded crank bolt, including:
Square taper
SRAM® PowerSpline®
BNI cranks for Bosch® e-bike systems
NOTE: For crank systems that use an M12 or M14 crank bolt, such as ISIS Drive or Octalink®, use the Park Tool CCP-44 or CWP-7.

CCP-44 FEATURES
Compatible with systems that use an M12 or M15 threaded crank bolt, including:
Shimano® Octalink®
ISIS Drive
ISIS Overdrive systems
NOTE: For crank systems that use an M8 or M10 crank bolt, such as square taper or PowerSpline®, use the Park Tool CCP-22 or CWP-7.

CWP-7 FEATURES
SMALL SWIVEL FOOT
Fits crank arms with M22 x 1.0 threads
Compatible with systems that use an M8 x 1.0 threaded crank bolt, including:
Square taper
SRAM® PowerSpline®
BNI cranks for Bosch® e-bike systems
LARGE SWIVEL FOOT
Fits crank arms with M22 x 1.0 threads
Compatible with systems that use an M12 x 1.0 or M15 x 1.0 threaded crank bolt, including:
Shimano® Octalink®
ISIS Drive
ISIS Overdrive systems

CC-3.2 FEATURES
5-to-10-speed chains: replace chain at or just before 0.75%
11-to-12-speed chains*: replace at or just before 0.5%
Check with manufacturer for specific replacement instructions
*Use the CC-4 for SRAM® Flattop™ and SRAM® T-Type 12-speed chains.

BBT-9 FEATURES
Fits 16-notch tool fittings with a major diameter (outside of notches) of 44–45 mm and a minor diameter (inside of notches) of 42.7 mm, including:
Shimano® BB80, BB5700, XT® BB70, BB51, and previous external bearing threaded cups
Threaded bottom bracket cups from Campagnolo®, Chris King®, FSA® MegaExo®, Hope™, SRAM®/Truvativ® GXP®, Race Face® X-type, Surly®, Wheels®, Fulcrum®, and others
16-notch disc brake rotor lockrings
16-notch Bafang® BBSH, BBS02 mid-drive motor lockrings
Fits 8-point tool fittings on Shimano® Hollowtech II® crank arm caps:
Equivalent to Shimano® TL-FC16 or TL-FC18 tool

PRESS
The DT-2 Rotor Truing Fork quickly became one of my favorites. It's a simple bar stock, with two different slots offering distinct leverage ratios to true rotors, meaning I don't have to do it barehanded with my thumbs against fingers for leverage. That method works, but the DT-2 keeps oil off the rotors and allows a bit more fine-tuning than the aforementioned digital manipulation

PS-1 FEATURES
• Thickness: 1.95 mm (0.08")
• Length: 162 mm (6.4")

CC-4 FEATURES
5-to-10-speed chains: replace chain at or just before 0.75%
11-to-12-speed chains: replace at or just before 0.5%
Check with manufacturer for specific replacement instructions

PW-5 FEATURES
Length: 11.5" (290 mm)
Weight: 256 g (9 oz.)

The FR-5.2 is designed to fit the most common tool fitting found on 7-to-12 speed cassette lockrings, including models made by Shimano®, SRAM®, and others. Also fits disc brake lockrings and lockring adapters with 12 internal splines, and top caps of some Rock Shox® suspension fork models. Thin wall construction allows use without removal of cones and locknuts. The 1" hexagonal base can be used in conjunction with a socket, wrench, or bench vise. Heat-treated alloy tool steel construction for a lifetime of use.

FR-5.2 FEATURES

Fits 12-spline tool fittings with an approximate outer diameter of 23.4 mm including:

• Cassette lockrings from Shimano®, SRAM® (including 1x), SunRace®, SunTour®, Chris King® and others

• Disc brake lockrings and lockring adapters with 12 internal splines from Shimano® and other brands

• Top cap of some Rock Shox® suspension fork models including Pike®, Lyrik™, SID®, Revelation™, Reba®, and Paragon™

Center bore for axle clearance is 12 mm.

The dependable design of our FR-5.2 lockring tool with an added 12 mm guide pin to stabilize the tool when used with thru axle hubs. The FR-5.2GT is designed to fit the most common tool fitting found on 7-to-12 speed cassette lockrings, including models made by Shimano®, SRAM®, and others. Also fits disc brake lockrings and lockring adapters with 12 internal splines. Thin wall construction allows use without removal of cones and locknuts. The 1" hexagonal base can be used in conjunction with a socket, wrench, or bench vise. Heat-treated alloy tool steel construction for a lifetime of use.

FR-5.2GT FEATURES

Fits 12-spline tool fittings with an approximate outer diameter of 23.4 mm including:

• Cassette lockrings from Shimano®, SRAM® (including 1x), SunRace®, SunTour®, Chris King® and others

• Disc brake lockrings and lockring adapters with 12 internal splines from Shimano® and other brands

When removing and installing bicycle components, having the right tools is essential. The Park Tool BBT-5/FR-11 is designed to fit the tool fittings found on Campagnolo® cassette lockrings and cartridge bottom brackets. Constructed from heat-treated alloy tool steel, the BBT-5/FR-11 features a 1" tool fitting for use with an adjustable wrench, socket, or bench vise.

BBT-5/FR-11 FEATURES

• Fits 12 spline/approx. 22.8 mm OD tool fittings

• Fits all Campagnolo® cassette lockrings

• Also fits Campagnolo® cartridge bottom brackets including Chorus® and Centaur®

• Base size for socket or wrench is 1" (25.4 mm)

NOTE: The BBT-5/FR-11 is not interchangeable with the FR-1.3, FR-5.2, or FR-7. Each tool fitting has its own unique tool profile.

The FR-4 is designed to fit the 20-spline tool fittings found on older SunTour® freewheels. Constructed from heat treated alloy tool steel, the FR-4 features a 1" tool fitting for use with an adjustable wrench, socket, or bench vise.

FR-4 FEATURES

• Fits 20-spline tool fittings with an approximate outer diameter of 21.6 mm

• Fits Atom®, Regina®, splined Zeus®, and some Schwinn®-approved freewheels

The FR-7 is designed to fit the 12-notch tool fittings found on Falcon® freewheels. Constructed from heat-treated alloy tool steel, the FR-7 features a 1" tool fitting for use with an adjustable wrench, socket, or bench vise.

FR-7 FEATURES

• Fits 12-spline/23 mm OD tool fittings

• Center bore for axle clearance is 10 mm

NOTE: The shape of the FR-7 looks similar to the FR-1.3 (for Shimano®, Sun Race®, Sachs® and similar freewheels). The FR-7, however, is made with a slightly larger outside diameter (23mm) to fit the Falcon® Freewheel. To make it easy to distinguish between the two removers, the FR-7 has a silver-colored plating. The slightly smaller diameter FR-1.3 is black.

The FR-1.3 is designed to fit the most common tool fitting found on 5-to-10 speed bicycle freewheel systems, including many models made by Shimano®, Sachs Aris®, SunRace®, Dimension®, and DNP Epoch™. Features an enlarged thru-hole to accommodate 14mm solid axles. The 1" hexagonal base can be used in conjunction with a 1" socket or adjustable wrench. Heat-treated alloy tool steel construction for a lifetime of use.

FR-1.3 FEATURES

• Fits 12-spline tool fittings with an approximate outer diameter of 22.6 mm

• Center bore for axle clearance is 15 mm

NOTE: For Falcon® freewheels, use the FR-7.